Extreme Networks Summit WM Series Guía de usuario Pagina 248
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System states and LEDs
Summit WM Series WLAN Switch and Altitude Access Point Software Version 4.1 User Guide
248
Table 18 shows the sequence of the Status and Activity LEDs.
Altitude AP system states
For the Altitude AP, the Status LED in the center also indicates power. The Status LED is dark when
unit is off and is green (solid) when the AP has completed discovery and is operational.
The chart below shows states and corresponding Status LED displays:
Table 18: Status and Activity LED sequence
System State Status LED Activity LED
Power up Off Off
Services started: WDTSTAT installed (init.d starts services) Blinking Amber Off
Startup Manager Task started Solid Amber Blinking Amber
Startup Manager Task completes startup – all components
started
Solid Green Blinking green, if traffic
Blank, if no traffic
A component fails to start or needs restarting (Startup Manager
Task retrying that component)
Solid Amber Blinking green
Summit WM series switch fails to boot Solid Red Off
A component fails (no more retries) Solid Red Off
System about to be reset by watchdog Blinking Red Off
Table 19: Altitude AP system states and status LED displays
State / Process Description LEDs
Power Altitude AP not powered. Off
Power Start up: Power On Self Test (POST) Steady green
(briefly)
Power Power On Self Test (POST) successful Off (briefly)
Discovery If the POST self test is successful, the AP begins Discovery process.
Altitude AP is powered on and searching for an active Summit WM
series switch. It sends a discover message and waits for a response
Orange (steady)
Fail to find DHCP Altitude AP failed to find DHCP (will stay in this state until a route
appears).
Red-orange
(alternate blink)
Failed discovery If there are SLP issues in failed discovery, the LED display changes. Green-orange
(alternate blink)
Registration Altitude AP learns the Summit WM series switch's IP address, and
can begin the Registration process
Orange (blink)
Failed Registration Altitude AP fails to learn the Summit WM series switch's IP address. Red (blink)
Standby 1 Altitude AP enters this state from Discovery when it encounters
an active Summit WM series switch and completes the
Registration process.
2 Altitude AP enters this state from Active when it receives a
control message from the Summit WM series switch to enter this
state. If the Altitude AP has any wireless device traffic, it will
drop the traffic.
Green (blink)
Altitude AP fails to register. It will wait 5 seconds and try again. Red (slow blink)
Firmware download from the Summit WM series switch is in progress Orange + green
(blink)
- Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Conventional wireless LANs 21
- Network traffic flow 25
- Network security 26
- Authentication 27
- WM Access Domain Services 28
- Mobility and roaming 29
- Network availability 29
- System Configuration Overview 30
- System configuration overview 34
- Configuring for remote access 35
- Setting up the data ports 42
- ● Host Port 43
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up static routes 45
- Setting up OSPF Routing 47
- 3 Configuring the Altitude AP 55
- Altitude AP radios 56
- Altitude AP discovery 57
- Registration after discovery 58
- Security mode 60
- Discovery timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- America 74
- Copy to Defaults feature 79
- Controlled Upgrade settings 84
- WM-AD overview 85
- Setting up a WM-AD checklist 86
- Topology of a WM-AD 87
- RF assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final filter rule 91
- Filtering sequence 91
- WM-AD global settings 92
- Setting up a new WM-AD 96
- Topology for a WM-AD 98
- Enabling management traffic 100
- To create an AAA topology: 105
- Authentication for a WM-AD 108
- ● Select IP/Port 125
- ● DNS (IP of DNS server) 126
- Default filter examples 132
- Privacy for a WM-AD for AAA 138
- Table 12: Service classes 143
- QoS modes 144
- Table 15: Queues 145
- Bridging traffic locally 149
- ● Tagged 150
- ● Untagged 150
- Availability overview 153
- Availability prerequisites 154
- Viewing SLP activity 156
- To view SLP activity: 157
- Mobility manager 159
- Defining management users 163
- Configuring network time 165
- To apply time zone settings: 166
- To set Network Time Protocol: 167
- Enabling SNMP 169
- To enable SNMP Parameters: 170
- Using controller utilities 171
- Trace Route 172
- Working with third-party APs 178
- Summit spy overview 179
- Running Summit Spy scans 181
- Analysis engine overview 183
- Working with friendly APs 186
- To delete a friendly AP: 187
- To modify a friendly AP: 187
- To maintain the Altitude APs: 189
- Viewing the displays 191
- To view reports and displays: 192
- Viewing reports 198
- To view reports: 199
- Disassociating a client 203
- Blacklisting a client 204
- To change the log levels: 208
- To set a poll interval: 209
- ● Halt system: reboot 210
- To upload a new backup: 215
- To delete a backup: 216
- To schedule a backup: 216
- To download for restore: 218
- To upload an image file: 219
- Logs including alarms 221
- To view logs: 222
- To view traces: 223
- To view audits: 224
- To clear logs: 225
- Performing system maintenance 226
- Glossary 227
- D (Continued) 229
- I (Continued) 233
- M (Continued) 235
- N (Continued) 236
- O (Continued) 237
- P (Continued) 238
- R (Continued) 239
- S (Continued) 240
- W (Continued) 244
- A System states and LEDs 247
- Altitude AP system states 248
- System states and LEDs 250
- B Regulatory Information 251
- EMI/EMC Standards 252
- Telecom Standards 252
- Physical and Environmental 253
- Part 15 Unlicensed Antenna 255
- European Community 257
- European Union 1999/5/EC 258
- European Spectrum Usage Rules 260
- Declarations of Conformity 262
- Regulatory Information 264
Relacionado con productos y manuales para Software Extreme Networks Summit WM Series
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales