Extreme Networks PoS Guía de usuario Pagina 136
- Pagina / 178
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-88 Packet Over SONET Module Installation and User Guide
Configuring the PoS Module
Adding a Port to an APS Group
To add a SONET port to an APS group, use the following command:
config aps <group#> add <port> [working | protection <ipaddress>]
The group# parameter is an integer in the range from 1 to 65535 that identifies the APS
group to which the specified port is to be added.
The
port parameter identifies the SONET port that is to be added to the APS group.
You must also specify whether the port is the APS working or protection line. You can
add only one working line and one protection line to an APS group. If you designate
the port the protection line, then you must also specify the IP address (
ipaddress
parameter) of the BlackDiamond switch where the working line resides. This IP address
is used to send APS control messages to the BlackDiamond switch containing the
working line.
The configured IP address should be associated with an Ethernet VLAN that has
loopback mode enabled to minimize the impact of network outages on APS
functionality. Also, when using APS to protect links on different BlackDiamond
6800 series switches, the network connecting the working and protection
switches must always have sufficient bandwidth to support APS control transfers.
In routing configurations, the working line and the protection line should represent the
same IP address from the perspective of the neighboring PPP switch. When the working
line and protection line reside in the same BlackDiamond switch, both ports should be
members of the same VLAN. The case where both the working line and the protection
line for an APS group reside in the same BlackDiamond switch is the only situation
where IPCP can be enabled on multiple SONET ports that are members of the same
VLAN. In general, if IPCP is enabled on a PoS module port, that port can be a member
of only one VLAN and no other ports on that switch can be members of that VLAN.
The following command example adds port 1 of the module installed in slot 8 of the
BlackDiamond switch to APS group 1001 as the working line.
config aps 1001 add 8:1 working
- Packet Over SONET 1
- Module Installation and 1
- User Guide 1
- Contents 3
- 3 Configuring the PoS Module 4
- Contents v 5
- Related to the PoS Module 6
- Figures ix 9
- Ta bl es xi 11
- Introduction 13
- Conventions 14
- Related Publications 15
- Overview 17
- BlackDiamond I/O Modules 18
- About the PoS Modules 19
- Physical Description 20
- PoS Module LED Indicators 21
- Service Ports 21
- Feature Summary 23
- Function Summary 25
- Jumbo Frames 26
- Service Provider Features 27
- NetFlow Statistics 28
- Installing or Replacing a 31
- PoS Module 31
- Cables and Connectors 33
- Safety Information 34
- I/O Module Slot Locations 35
- 1234AB5678 36
- LED Indicators 40
- Troubleshooting 41
- Fixing Configuration Errors 43
- Fixing Power-Related Problems 45
- Fixing Link Down Problems 45
- Tools and Equipment 46
- Removing an I/O Module 47
- BlackDiamond 1 52
- BlackDiamond 2 52
- Routing Over PoS Ports 54
- APS Port Redundancy 56
- APS Module Redundancy 57
- APS Switch Redundancy 58
- Configuring SONET Framing 61
- Configuring SONET Clocking 62
- -error_rate 63
- Configuring the Signal Label 65
- SONET Events 67
- PPP Background Information 70
- VLAN xVLAN a 72
- IP Router 72
- Configuring the PoS Checksum 75
- Configuring PoS Scrambling 75
- Configuring Link Maintenance 76
- Displaying PPP Information 84
- Configuring a QoS Profile 92
- Configuring DiffServ 95
- DiffServ Classification 96
- Enhanced RED Support 99
- Configuring the PoS Module 100
- Configuring QoS Functions 101
- QoS Monitor 107
- Intra-Subnet QoS 107
- Export Criteria 112
- Unconfiguring Flow Statistics 120
- BlackDiamond 123
- Protection line 123
- Working line 123
- Virtual router 124
- Virtual APS router 127
- 192.168.10.1 192.168.10.2 127
- SONETPoS PoS 127
- Neighbor PPP router 127
- APS Benefits 130
- Table 3-16: APS Commands 134
- Enabling and Disabling APS 135
- Adding a Port to an APS Group 136
- Configuring APS Timers 139
- Configuring APS Lockout 140
- MIB Support for APS 144
- Configuring Port Tunneling 145
- Customer 146
- Configuring Port Attributes 150
- Jumbo Frame Support 152
- Configuring IGMP Attributes 153
- ExtremeWare Command 155
- New ExtremeWare Commands 156
- New Commands 157
- Changed Commands 159
- Supported MIBs and Standards 165
- SONET/SDH Support 166
- PPP Support 166
- QoS and DiffServ Support 167
- Flow Statistics Support 168
- Standards Supported for APS 169
- MIBs Supported for APS 169
- Numerics 171
- Index of Commands 177
Relacionado con productos y manuales para Redes Extreme Networks PoS
Redes Extreme Networks WM-4T1i Guía de usuario
(46 paginas)
(46 paginas)
Redes Extreme Networks WM-4T1i Guía de usuario
(38 paginas)
(38 paginas)
Redes Extreme Networks Altitude 3550 Especificaciones
(308 paginas)
(308 paginas)
Redes Extreme Networks WM200 Especificaciones
(210 paginas)
(210 paginas)
Redes Extreme Networks WM200 Especificaciones
(126 paginas)
(126 paginas)
Redes Extreme Networks WM-4T1i Especificaciones
(336 paginas)
(336 paginas)
Redes Extreme Networks AG200 Manual de usuario
(2 paginas)
(2 paginas)
Redes Extreme Networks WM200 Especificaciones
(130 paginas)
(130 paginas)
Redes Extreme Networks 300-2 Guía de instalación
(48 paginas)
(48 paginas)
Redes Extreme Networks WM2000 Manual de usuario
(3 paginas)
(3 paginas)
Redes Extreme Networks 300-2 Especificaciones
(62 paginas)
(62 paginas)
Redes Extreme Networks WM2000 Guía de usuario
(2 paginas)
(2 paginas)
Redes Extreme Networks WM-4T1i Especificaciones
(306 paginas)
(306 paginas)
Sony BDV-N5200W manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour mélangeurs/transformateurs d'aliments Sony BDV-N5200W.
Nous fournissons des manuels en pdf 5 Sony BDV-N5200W à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales