Extreme Networks WM20 Controller Guía de usuario Pagina 31
- Pagina / 270
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System Configuration Overview
Summit WM20 User Guide, Software Release 4.2 31
have the same configuration, this feature will expedite deployment, as an AP will automatically
receive full configuration (including WM-AD assignment) upon initial registration with the Summit
WM Controller.
6 Wireless AP Configuration – Modify properties or settings of the Wireless AP, if applicable.
7 WM Access Domain Services (WM-AD) Setup – Set up one or more virtual subnetworks on the
Summit WM Controller. For each WM-AD, configure the following:
● Top o lo gy – Configure the WM-AD.
● RF – Assign the Wireless APs’ radios to the WM-AD.
● Authentication and Accounting – Configure the authentication method for the wireless device
user and enable the accounting method.
● RAD Policy – Define filter ID values and WM-AD Groups.
● Filtering – Define filtering rules to control network access.
● Multicast – Define groups of IP addresses for multicast traffic.
● Privacy – Select and configure the wireless security method on the WM-AD.
● QoS Policy – Configure the Qos policy.
- Summit WM20 User Guide 1
- Table of Contents 3
- Formatting Conventions 10
- Documentation Feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Points and Software Solution 21
- ● Summit WM Controller 22
- ● Wireless APs 22
- Network Traffic Flow 25
- Network Security 26
- Authentication 27
- WM Access Domain Services 28
- Packet Filtering Policy 29
- Mobility and Roaming 29
- Network Availability 29
- System Configuration Overview 30
- Configuring for Remote Access 36
- Controller 37
- Setting up the Data Ports 42
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up Static Routes 45
- Setting up OSPF Routing 47
- Access Points and Software 53
- 3 Configuring the Wireless AP 55
- Wireless AP Radios 56
- Wireless AP Discovery 57
- Registration After Discovery 58
- Security Mode 60
- Discovery Timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- Default AP Configuration 79
- Copy to Defaults Feature 79
- Upgrade settings 84
- 4 WM Access Domain Services 85
- Setting up a WM-AD Checklist 86
- Topology of a WM-AD 87
- RF Assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final Filter Rule 91
- Filtering Sequence 91
- WM-AD Global Settings 92
- Setting up a New WM-AD 95
- Topology for a WM-AD 98
- Enabling Management Traffic 100
- To create an AAA topology: 105
- ● WM20 – Up to 8 WM-ADs 106
- Authentication for a WM-AD 108
- ● No Captive Portal Support 113
- ● AP Serial number 115
- ● AP Name 115
- ● WM-AD Name 115
- ● MAC Address 115
- ● WM-AD’s 118
- ● Select IP/Port 124
- ● DNS (IP of DNS server) 125
- ● Allows only HTTP traffic 127
- Default Filter Examples 131
- ● 64-bit 135
- ● 128-bit 135
- ● 152-bit 135
- Privacy for a WM-AD for AAA 137
- Table 12: Service Classes 142
- QoS Modes 143
- Table 15: Queues 144
- CS7 7/7 AF32 4/4 146
- Bridging Traffic Locally 148
- ● Untagged 149
- Availability Overview 151
- Availability Prerequisites 152
- Viewing SLP Activity 155
- Defining Management Users 157
- Configuring Network Time 158
- To apply time zone settings: 159
- To set Network Time Protocol: 159
- Enabling SNMP 162
- To enable SNMP Parameters: 163
- Using Controller Utilities 164
- To set up third-party APs: 169
- Working With Third-Party APs 172
- Summit WM Series Spy Overview 173
- ● Scan Groups 175
- ● Friendly APs 175
- ● Third-party APs 175
- ● AP Maintenance 175
- Analysis Engine Overview 176
- Working With Friendly APs 179
- To add friendly APs manually: 180
- To delete a friendly AP: 180
- To modify a friendly AP: 180
- To maintain the Wireless APs: 181
- Viewing the Displays 185
- To view reports and displays: 186
- Displays 189
- Viewing Reports 190
- To view reports: 191
- Disassociating a Client 195
- Blacklisting a client 196
- To change the log levels: 200
- To set a poll interval: 201
- Maintenance 202
- To upload a new backup: 207
- To delete a backup: 207
- To schedule a backup: 207
- To download for restore: 209
- To upload an image file: 210
- Logs and Traces 211
- To view logs: 212
- To view traces: 213
- To view audits: 214
- To clear logs: 215
- Performing System Maintenance 216
- Glossary 217
- D (Continued) 219
- I (Continued) 223
- M (Continued) 225
- N (Continued) 226
- O (Continued) 227
- P (Continued) 228
- R (Continued) 229
- S (Continued) 230
- V (Continued) 234
- Terms and Abbreviations 235
- A Summit WM20 Controller 237
- Summit WM20 Controller Panels 238
- Summit WM20 Controller’s LEDs 239
- B Regulatory Information 241
- EMI/EMC Standards 242
- Environmental Conditions 242
- Operational Environment: 243
- Detach. AP (15939) 244
- FCC ID#: RJF-A3502A 245
- Part 15 Unlicensed Antenna 246
- European Community 247
- European Union 1999/5/EC 248
- European Spectrum Usage Rules 250
- Declarations of Conformity 252
- Detach. (15939) Access Points 253
- Antenna Diversity 254
- Regulatory Information 256
- RF Safety Distance 258
- Professional Installation 258
Relacionado con productos y manuales para Software Extreme Networks WM20 Controller
(32 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales