Extreme Networks WM-4T1i Especificaciones Pagina 67
- Pagina / 306
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Extreme Networks Consolidated Hardware Guide 2-23
Meeting Power Requirements
AC Power Cord Requirements
The AC power cord must be approved for the country where it is used. Table 2-2
describes AC power cord requirements.
Note: When using dual power supplies, make sure that each AC power supply
attaches to an independent power source.
Replacing the Power Cord
If the power cord plug is unsuitable and must be replaced, connect the power supply
wires for the switch according to the following scheme:
• Brown wire to the Live (Line) plug terminal, which may be marked with the letter
“L” or colored red.
• Blue wire to the Neutral plug terminal, which may be marked with the letter “N” or
colored black.
• Yellow/Green wire to the Ground plug terminal, which may be marked with the
letter “E” (the Earth symbol) or colored yellow/green.
Uninterruptable Power Supply Requirements
An uninterruptible power supply (UPS) is a device that sits between a power supply
(such as a wall outlet) and a device (such as a switch) to prevent outages, sags, surges,
and bad harmonics from adversely affecting the performance of the device.
Table 2-2: AC Power Cord Requirements
Country Requirements
USA and Canada ■ The cord set must be UL-approved and CSA-certified.
■ The minimum specification for the flexible cord is No. 18
AWG (1.5 mm
2
), Type SVT or SJT, 3-conductor.
■ The cord set must have a rated current capacity of at least
the amount rated for each specific product.
■ The attachment plug must be an Earth-grounding type with
a NEMA 5-15P (10 A, 125 V) configuration.
Denmark The supply plug must comply with section 107-2-D1, standard
DK2-1a or DK2-5a.
Switzerland The supply plug must comply with SEV/ASE 1011.
Argentina The supply plug must comply with Argentinian standards.
- Extreme Networks 1
- Consolidated Hardware 1
- Contents 3
- Part 2: Site Planning 4
- Part 3: Summit Switch 4
- 4 Summit Switch Models 5
- 5 Summit Switch Installation 7
- Part 4: Alpine Switch 8
- Part 5: BlackDiamond Switch 10
- Part 6: Switch Operation 12
- Part 7: Appendices 12
- B Technical Specifications 13
- Introduction 21
- Conventions 22
- Related Publications 23
- About This Guide 23
- How To Use This Guide 24
- Common Features 25
- Summary of Common Switch 27
- Features 27
- Full-Duplex Support 28
- Management Ports 28
- GBIC Types and Specifications 33
- ZX GBIC ZX GBIC 38
- LX70 LX70 38
- ZX GBIC LX70 38
- Module A 40
- Module B 40
- Site Planning 43
- Site Preparation 45
- Planning Your Site 46
- Building and Electrical Codes 47
- Wiring Closet Considerations 49
- Meeting Site Requirements 51
- Electrostatic Discharge (ESD) 54
- ESD strap 55
- Connected 55
- Securing the Rack 57
- Secure to floor 58
- Cabling Standards 59
- Installing Cable 59
- Fiber Optic Cable 62
- Cable Distances 62
- RJ-45 Connector Jackets 63
- 0.1" = 1mm actual 64
- 39.37% : 254% 64
- Radio Frequency Interference 65
- Meeting Power Requirements 66
- Replacing the Power Cord 67
- UPS Features 68
- Selecting a UPS 68
- UPS Transition Time 69
- Summit Switch 71
- Summit Switch Overview 73
- Summary of Features 74
- Summit24e2 75
- Summit24e3 75
- Memory Requirements 76
- • Summit24e3 on page 4-32 80
- • SummitPx1 on page 4-35 80
- Summit1i Switch Front View 81
- Summit1i Switch Rear View 82
- Serial Number 83
- Console Port 83
- Summit5i Switch Front View 84
- 13 161514 85
- 4321 8765 85
- AC Connectors Console port 86
- Ethernet port 86
- Management Port 87
- Summit7i Switch Front View 88
- GBIC Ports 89
- Modem Port 90
- PCMCIA Slot 90
- Power socket 91
- Summit48i Switch Front View 93
- Summit48si Switch Front View 96
- Power socketPSU status LEDs 97
- Summit48si Switch LEDs 100
- Summit4 Switch Front View 101
- Summit4/FX Switch Front View 102
- Summit24 Switch Front View 103
- Summit48 Switch Front View 104
- Reset button 105
- MAC Address 106
- Reset Button 106
- Summit48 switches 107
- Summit24e2 Switch Front View 108
- Summit24e2 Switch Rear View 108
- Summit24e2 Switch LEDs 109
- Summit24e3 Switch Front View 110
- Summit24e3 Switch Rear View 111
- Summit24e3 Switch LEDs 112
- GBIC Network Interface 113
- Ethernet Management Port 113
- Power socket and fus 114
- Summit Switch Models 116
- Summit Switch Installation 117
- BDbrackt 118
- Mounting the Switch in a Rack 119
- Supplies 120
- Retaining bracket screw 122
- Alpine Switch 125
- Alpine 3800 Series Switch 127
- Overview 127
- Switch Components 129
- Alpine 3808 Switch 130
- Alpine 3804 Switch 130
- Alpine 3802 Switch 130
- Safety Information 131
- Alpine 3808 Switch Rear View 135
- Alpine 3804 Switch Front View 136
- 38_rear4 138
- 3802chas 139
- Alpine 3802 Switch LEDs 140
- Power Sockets 141
- New Error Messages 142
- New Command 142
- Updated Commands 142
- Installing the Chassis 143
- 38_rack8 145
- 38_rack4 146
- 3802rack 146
- Removing the Chassis 147
- Power Supplies 149
- Power Supply LEDs 150
- SLIDE TO REMOVE 152
- Selecting the Cabling 155
- Installing the Power Supply 155
- SLIDE TO 156
- WHEN INS 158
- Attaching the Cabling 159
- Management Module 161
- SMMi Memory 162
- Installing SMMi Modules 163
- Removing SMMi Modules 165
- Configuring I/O Modules 167
- Module status 169
- Port status LEDs 169
- Gigabit Ethernet ports 170
- 1000 Mbps ports 171
- Module status LEDs 172
- Port status LEDs 4 Gbps port 172
- Software Requirements 173
- FM-32Ti Module 174
- Port status LEDs VDSL ports 178
- Module status LED 178
- I/O Module LEDs 184
- Access I/O Module LEDs 184
- Installing I/O Modules 185
- Removing I/O Modules 186
- Alpine 3808 Fan Tray 189
- Alpine 3804 Fan Tray 190
- Alpine 3802 Fan Tray 190
- Fan Tray 191
- 38_fanx8 192
- BlackDiamond Switch 195
- BlackDiamond 6800 Series 197
- Switch Overview 197
- Port Connections 199
- BlackDiamond Power Supplies 201
- Following Safety Information 202
- Switch Chassis 203
- BD_6816s 205
- BD_rr16s 206
- V-50/60Hz 208
- 200-240V, 15A 208
- Fan tray 209
- BD_rack16 212
- Switch Power Supplies 215
- 220 VAC Power Supplies 216
- 110 VAC Power Supplies 217
- DC Power Supplies 218
- -48V RET 220
- AC Power Cable and Plug 222
- Wider prong 223
- Selecting the DC Cabling 224
- Preparing the DC Cabling 224
- Cable retention screw 225
- Management Switch Module 229
- BlackDiamond 6808 1 230
- 128 Gbps 230
- MSM64i Activity 231
- MSM64i Memory 232
- MSM64i LEDs 233
- Installing MSM64i Modules 234
- Removing MSM64i Modules 237
- BlackDiamond 6800 Series I/O 239
- 100/1000 Mbps ports 240
- G12SXi Module 242
- Channel status LEDs 244
- 10,000 Mbps port 244
- 10/100 Mbps ports 247
- 100 Mbps 251
- P3cSi and P3cMi Modules 253
- P12cSi and P12cMi Modules 255
- A3cSi Module 261
- Switch Fan Tray 265
- BlackDiamond 6808 Fan Tray 266
- Switch Operation 271
- Powering On the Switch 273
- Verifying the Installation 274
- Cable connector: 9-pin female 276
- Logging In for the First Time 277
- Appendices 279
- Power Cord 282
- Connections 283
- Lithium Battery 284
- Technical Specifications 285
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales