Extreme Networks Summit WM Series Guía de usuario Pagina 171
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using controller utilities
Summit WM Series WLAN Switch and Altitude Access Point Software Version 4.1 User Guide
171
3 Type: the following information:
● Contact Name – Specifies the name of SNMP administrator.
● Location – Specifies the location of the SNMP administration machine.
● Read Community Name – Specifies the community name for users with read privileges.
● Read/Write Community Name – Specifies the community name for users with read and write
privileges.
● SNMP Trap Port – Specifies the destination port for SNMP traps. The industry standard is 162. If
left blank, no traps are generated.
● Forward Traps – Specifies the security level of the traps to be forwarded. From the drop-down
list, select Informational, Minor, Major, or Critical.
● Manager A – Specifies the IP address of the specific machine on the network where the SNMP
traps are monitored.
● Manager B – Specifies the IP address of a second machine on the network where the SNMP traps
are monitored, if Manager A is not available.
NOTE
For security purposes, it is recommended that you immediately change the Read Community Name (public) and
the Read/Write Community Name (private) to names that are less obvious and more secure.
Using controller utilities
You can use Summit WM series switch utilities to test a connection to the target IP address or to record
the route through the Internet between your computer and the target IP address.
To test or record IP address connections:
1 From the main menu, click Summit Switch Configuration. The Summit Switch Configuration
screen is displayed.
2 In the left pane, click Utilities. The Summit Switch Utilities screen is displayed.
3 In the Target IP Address box, type the IP address of the destination computer.
4 To test a connection to the target IP address, click Ping.
- Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Conventional wireless LANs 21
- Network traffic flow 25
- Network security 26
- Authentication 27
- WM Access Domain Services 28
- Mobility and roaming 29
- Network availability 29
- System Configuration Overview 30
- System configuration overview 34
- Configuring for remote access 35
- Setting up the data ports 42
- ● Host Port 43
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up static routes 45
- Setting up OSPF Routing 47
- 3 Configuring the Altitude AP 55
- Altitude AP radios 56
- Altitude AP discovery 57
- Registration after discovery 58
- Security mode 60
- Discovery timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- America 74
- Copy to Defaults feature 79
- Controlled Upgrade settings 84
- WM-AD overview 85
- Setting up a WM-AD checklist 86
- Topology of a WM-AD 87
- RF assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final filter rule 91
- Filtering sequence 91
- WM-AD global settings 92
- Setting up a new WM-AD 96
- Topology for a WM-AD 98
- Enabling management traffic 100
- To create an AAA topology: 105
- Authentication for a WM-AD 108
- ● Select IP/Port 125
- ● DNS (IP of DNS server) 126
- Default filter examples 132
- Privacy for a WM-AD for AAA 138
- Table 12: Service classes 143
- QoS modes 144
- Table 15: Queues 145
- Bridging traffic locally 149
- ● Tagged 150
- ● Untagged 150
- Availability overview 153
- Availability prerequisites 154
- Viewing SLP activity 156
- To view SLP activity: 157
- Mobility manager 159
- Defining management users 163
- Configuring network time 165
- To apply time zone settings: 166
- To set Network Time Protocol: 167
- Enabling SNMP 169
- To enable SNMP Parameters: 170
- Using controller utilities 171
- Trace Route 172
- Working with third-party APs 178
- Summit spy overview 179
- Running Summit Spy scans 181
- Analysis engine overview 183
- Working with friendly APs 186
- To delete a friendly AP: 187
- To modify a friendly AP: 187
- To maintain the Altitude APs: 189
- Viewing the displays 191
- To view reports and displays: 192
- Viewing reports 198
- To view reports: 199
- Disassociating a client 203
- Blacklisting a client 204
- To change the log levels: 208
- To set a poll interval: 209
- ● Halt system: reboot 210
- To upload a new backup: 215
- To delete a backup: 216
- To schedule a backup: 216
- To download for restore: 218
- To upload an image file: 219
- Logs including alarms 221
- To view logs: 222
- To view traces: 223
- To view audits: 224
- To clear logs: 225
- Performing system maintenance 226
- Glossary 227
- D (Continued) 229
- I (Continued) 233
- M (Continued) 235
- N (Continued) 236
- O (Continued) 237
- P (Continued) 238
- R (Continued) 239
- S (Continued) 240
- W (Continued) 244
- A System states and LEDs 247
- Altitude AP system states 248
- System states and LEDs 250
- B Regulatory Information 251
- EMI/EMC Standards 252
- Telecom Standards 252
- Physical and Environmental 253
- Part 15 Unlicensed Antenna 255
- European Community 257
- European Union 1999/5/EC 258
- European Spectrum Usage Rules 260
- Declarations of Conformity 262
- Regulatory Information 264
Relacionado con productos y manuales para Software Extreme Networks Summit WM Series
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales