Extreme Networks Summit WM Series Guía de usuario Pagina 36
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring the Summit WM series switch
Summit WM Series WLAN Switch and Altitude Access Point Software Version 4.1 User Guide
36
will expedite deployment, as an AP will automatically receive full configuration (including WM-AD
assignment) upon initial registration with the Summit WM series switch. If applicable, modify the
properties or settings of the Altitude APs.
For more information, see Chapter 5, “WM Access Domain Services configuration.”
Step 7 – Confirming the AP firmware version
Confirm the latest firmware version is loaded. For more information, see “Performing Altitude AP
software maintenance” on page 81.
Performing the first-time setup of the Summit WM
series switch
Before you can connect the Summit WM series switch to the enterprise network, you must change the
IP address of the Summit WM series switch management port from its factory default to the IP address
suitable for your enterprise network. Access the Summit WM series switch by one of two methods:
● Use a device supporting VT100 emulation, attached to the DB9 serial port (COM1 port) of the
Summit WM series switch via a cross-over (null modem) cable. Use the Command Line Interface
(CLI) commands. For more information, see the Summit WM Series WLAN Switch and Altitude Access
Points Software CLI Reference Guide.
● Use a laptop computer with a Web browser. Connect the supplied cross-over Ethernet cable between
the laptop and management Ethernet port of the Summit WM series switch. Follow the steps below.
Accessing the Summit WM series switch
1 Statically assign an unused IP address in the 192.168.10.0/24 subnet for the Ethernet port of the
computer. For example, 192.168.10.205.
2 Launch your Web browser (Internet Explorer version 6.0 or higher, or FireFox).
3 In the browser address bar, type the following:
https://192.168.10.1:5825
This launches the Summit Wireless Assistant. The logon screen is displayed.
- Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Conventional wireless LANs 21
- Network traffic flow 25
- Network security 26
- Authentication 27
- WM Access Domain Services 28
- Mobility and roaming 29
- Network availability 29
- System Configuration Overview 30
- System configuration overview 34
- Configuring for remote access 35
- Setting up the data ports 42
- ● Host Port 43
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up static routes 45
- Setting up OSPF Routing 47
- 3 Configuring the Altitude AP 55
- Altitude AP radios 56
- Altitude AP discovery 57
- Registration after discovery 58
- Security mode 60
- Discovery timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- America 74
- Copy to Defaults feature 79
- Controlled Upgrade settings 84
- WM-AD overview 85
- Setting up a WM-AD checklist 86
- Topology of a WM-AD 87
- RF assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final filter rule 91
- Filtering sequence 91
- WM-AD global settings 92
- Setting up a new WM-AD 96
- Topology for a WM-AD 98
- Enabling management traffic 100
- To create an AAA topology: 105
- Authentication for a WM-AD 108
- ● Select IP/Port 125
- ● DNS (IP of DNS server) 126
- Default filter examples 132
- Privacy for a WM-AD for AAA 138
- Table 12: Service classes 143
- QoS modes 144
- Table 15: Queues 145
- Bridging traffic locally 149
- ● Tagged 150
- ● Untagged 150
- Availability overview 153
- Availability prerequisites 154
- Viewing SLP activity 156
- To view SLP activity: 157
- Mobility manager 159
- Defining management users 163
- Configuring network time 165
- To apply time zone settings: 166
- To set Network Time Protocol: 167
- Enabling SNMP 169
- To enable SNMP Parameters: 170
- Using controller utilities 171
- Trace Route 172
- Working with third-party APs 178
- Summit spy overview 179
- Running Summit Spy scans 181
- Analysis engine overview 183
- Working with friendly APs 186
- To delete a friendly AP: 187
- To modify a friendly AP: 187
- To maintain the Altitude APs: 189
- Viewing the displays 191
- To view reports and displays: 192
- Viewing reports 198
- To view reports: 199
- Disassociating a client 203
- Blacklisting a client 204
- To change the log levels: 208
- To set a poll interval: 209
- ● Halt system: reboot 210
- To upload a new backup: 215
- To delete a backup: 216
- To schedule a backup: 216
- To download for restore: 218
- To upload an image file: 219
- Logs including alarms 221
- To view logs: 222
- To view traces: 223
- To view audits: 224
- To clear logs: 225
- Performing system maintenance 226
- Glossary 227
- D (Continued) 229
- I (Continued) 233
- M (Continued) 235
- N (Continued) 236
- O (Continued) 237
- P (Continued) 238
- R (Continued) 239
- S (Continued) 240
- W (Continued) 244
- A System states and LEDs 247
- Altitude AP system states 248
- System states and LEDs 250
- B Regulatory Information 251
- EMI/EMC Standards 252
- Telecom Standards 252
- Physical and Environmental 253
- Part 15 Unlicensed Antenna 255
- European Community 257
- European Union 1999/5/EC 258
- European Spectrum Usage Rules 260
- Declarations of Conformity 262
- Regulatory Information 264
Relacionado con productos y manuales para Software Extreme Networks Summit WM Series
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales