Extreme Networks Summit WM Series Guía de usuario Pagina 75
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Modifying Altitude AP settings
Summit WM Series WLAN Switch and Altitude Access Point Software Version 4.1 User Guide
75
● No of Retries for Video VI – Select the number of retries for the Video transmission queue. The
default value is 4. The recommended setting is adaptive (multi-rate).
● No of Retries for Voice VO – Select the number of retries for the Voice transmission queue. The
default value is 1. The recommended setting is adaptive (multi-rate).
● No of Retries for Turbo Voice TVO – Select the number of retries for the Turbo Voice
transmission queue. The default value is 1. The recommended setting is adaptive (multi-rate).
4 To save your changes, click Save.
Setting up the Altitude AP using static configuration
The Altitude AP static configuration feature provides the Summit WM series switch, access points, and
WLAN switch software solution with the capability for a network with either a central office or a
branch office model. The static configuration settings assist in the setup of branch office support. These
settings are not dependent of branch topology, but instead can be employed at any time if required. In
the branch office model, Altitude APs are installed in remote sites, while the Summit WM series switch
is in the central office. The Altitude APs require the capability to interact in both the local site network
and the central network. To achieve this model, a static configuration is used.
NOTE
If an Altitude AP with a statically configured IP address (without a statically configured Summit Switch Search List)
cannot register with the Summit WM series switch within the specified number of retries, the Altitude AP will use
SLP, DNS, and SLP multicast as a backup mechanism.
To set up an Altitude AP using static configuration:
1 From the main menu, click Altitude AP Configuration. The Altitude AP screen is displayed.
2 Click the appropriate Altitude AP in the list.
- Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Conventional wireless LANs 21
- Network traffic flow 25
- Network security 26
- Authentication 27
- WM Access Domain Services 28
- Mobility and roaming 29
- Network availability 29
- System Configuration Overview 30
- System configuration overview 34
- Configuring for remote access 35
- Setting up the data ports 42
- ● Host Port 43
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up static routes 45
- Setting up OSPF Routing 47
- 3 Configuring the Altitude AP 55
- Altitude AP radios 56
- Altitude AP discovery 57
- Registration after discovery 58
- Security mode 60
- Discovery timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- America 74
- Copy to Defaults feature 79
- Controlled Upgrade settings 84
- WM-AD overview 85
- Setting up a WM-AD checklist 86
- Topology of a WM-AD 87
- RF assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final filter rule 91
- Filtering sequence 91
- WM-AD global settings 92
- Setting up a new WM-AD 96
- Topology for a WM-AD 98
- Enabling management traffic 100
- To create an AAA topology: 105
- Authentication for a WM-AD 108
- ● Select IP/Port 125
- ● DNS (IP of DNS server) 126
- Default filter examples 132
- Privacy for a WM-AD for AAA 138
- Table 12: Service classes 143
- QoS modes 144
- Table 15: Queues 145
- Bridging traffic locally 149
- ● Tagged 150
- ● Untagged 150
- Availability overview 153
- Availability prerequisites 154
- Viewing SLP activity 156
- To view SLP activity: 157
- Mobility manager 159
- Defining management users 163
- Configuring network time 165
- To apply time zone settings: 166
- To set Network Time Protocol: 167
- Enabling SNMP 169
- To enable SNMP Parameters: 170
- Using controller utilities 171
- Trace Route 172
- Working with third-party APs 178
- Summit spy overview 179
- Running Summit Spy scans 181
- Analysis engine overview 183
- Working with friendly APs 186
- To delete a friendly AP: 187
- To modify a friendly AP: 187
- To maintain the Altitude APs: 189
- Viewing the displays 191
- To view reports and displays: 192
- Viewing reports 198
- To view reports: 199
- Disassociating a client 203
- Blacklisting a client 204
- To change the log levels: 208
- To set a poll interval: 209
- ● Halt system: reboot 210
- To upload a new backup: 215
- To delete a backup: 216
- To schedule a backup: 216
- To download for restore: 218
- To upload an image file: 219
- Logs including alarms 221
- To view logs: 222
- To view traces: 223
- To view audits: 224
- To clear logs: 225
- Performing system maintenance 226
- Glossary 227
- D (Continued) 229
- I (Continued) 233
- M (Continued) 235
- N (Continued) 236
- O (Continued) 237
- P (Continued) 238
- R (Continued) 239
- S (Continued) 240
- W (Continued) 244
- A System states and LEDs 247
- Altitude AP system states 248
- System states and LEDs 250
- B Regulatory Information 251
- EMI/EMC Standards 252
- Telecom Standards 252
- Physical and Environmental 253
- Part 15 Unlicensed Antenna 255
- European Community 257
- European Union 1999/5/EC 258
- European Spectrum Usage Rules 260
- Declarations of Conformity 262
- Regulatory Information 264
Relacionado con productos y manuales para Software Extreme Networks Summit WM Series
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.315 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales