Extreme Networks Summit WM Series Guía de usuario Pagina 79
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Modifying an Altitude AP’s properties based on a default AP configuration
Summit WM Series WLAN Switch and Altitude Access Point Software Version 4.1 User Guide
79
NOTE
If SSID Broadcast is disabled and DRM is enabled, you must provide an RF Domain ID.
9 From the Minimum drop-down list, select the minimum power level below which the power cannot
be further reduced by the DRM.
10 From the Maximum drop-down list, select the maximum power level above which the power cannot
be further increased by the DRM.
NOTE
Due to limited power control resolution, the actual power limits may differ slightly from the settings you define.
11 Click Apply to selected APs.
12 To save your changes, click Save.
13 To re-establish baseline settings, forcing the APs to go through the auto-channel selection process,
click Reset DRM. This will cause all APs using DRM to reboot and rerun the auto-channel selection
algorithm.
Modifying an Altitude AP’s properties based on a
default AP configuration
If you have an Altitude AP that is already configured with its own settings, but would like the Altitude
AP to be reset to use the system’s default AP settings, use the Reset to Defaults feature on the AP
Properties tab.
To configure an Altitude AP with the system’s default AP settings:
1 From the main menu, click Altitude AP Configuration. The Altitude AP screen is displayed.
2 In the Altitude AP list, click the Altitude AP whose properties you want to modify. The AP
Properties tab displays Altitude AP information.
3 Click Reset to Defaults to have the Altitude AP inherit the system’s default AP settings. A pop-up
window asking you to confirm the configuration change is displayed.
4 Click OK to confirm resetting the AP to the default settings.
Modifying the Altitude AP’s default setting using the
Copy to Defaults feature
You can modify the system’s default AP settings by using the Copy to Defaults feature on the AP
Properties tab. This feature allows the properties of an already configured AP to become the system’s
default AP settings.
- Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Conventional wireless LANs 21
- Network traffic flow 25
- Network security 26
- Authentication 27
- WM Access Domain Services 28
- Mobility and roaming 29
- Network availability 29
- System Configuration Overview 30
- System configuration overview 34
- Configuring for remote access 35
- Setting up the data ports 42
- ● Host Port 43
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up static routes 45
- Setting up OSPF Routing 47
- 3 Configuring the Altitude AP 55
- Altitude AP radios 56
- Altitude AP discovery 57
- Registration after discovery 58
- Security mode 60
- Discovery timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- America 74
- Copy to Defaults feature 79
- Controlled Upgrade settings 84
- WM-AD overview 85
- Setting up a WM-AD checklist 86
- Topology of a WM-AD 87
- RF assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final filter rule 91
- Filtering sequence 91
- WM-AD global settings 92
- Setting up a new WM-AD 96
- Topology for a WM-AD 98
- Enabling management traffic 100
- To create an AAA topology: 105
- Authentication for a WM-AD 108
- ● Select IP/Port 125
- ● DNS (IP of DNS server) 126
- Default filter examples 132
- Privacy for a WM-AD for AAA 138
- Table 12: Service classes 143
- QoS modes 144
- Table 15: Queues 145
- Bridging traffic locally 149
- ● Tagged 150
- ● Untagged 150
- Availability overview 153
- Availability prerequisites 154
- Viewing SLP activity 156
- To view SLP activity: 157
- Mobility manager 159
- Defining management users 163
- Configuring network time 165
- To apply time zone settings: 166
- To set Network Time Protocol: 167
- Enabling SNMP 169
- To enable SNMP Parameters: 170
- Using controller utilities 171
- Trace Route 172
- Working with third-party APs 178
- Summit spy overview 179
- Running Summit Spy scans 181
- Analysis engine overview 183
- Working with friendly APs 186
- To delete a friendly AP: 187
- To modify a friendly AP: 187
- To maintain the Altitude APs: 189
- Viewing the displays 191
- To view reports and displays: 192
- Viewing reports 198
- To view reports: 199
- Disassociating a client 203
- Blacklisting a client 204
- To change the log levels: 208
- To set a poll interval: 209
- ● Halt system: reboot 210
- To upload a new backup: 215
- To delete a backup: 216
- To schedule a backup: 216
- To download for restore: 218
- To upload an image file: 219
- Logs including alarms 221
- To view logs: 222
- To view traces: 223
- To view audits: 224
- To clear logs: 225
- Performing system maintenance 226
- Glossary 227
- D (Continued) 229
- I (Continued) 233
- M (Continued) 235
- N (Continued) 236
- O (Continued) 237
- P (Continued) 238
- R (Continued) 239
- S (Continued) 240
- W (Continued) 244
- A System states and LEDs 247
- Altitude AP system states 248
- System states and LEDs 250
- B Regulatory Information 251
- EMI/EMC Standards 252
- Telecom Standards 252
- Physical and Environmental 253
- Part 15 Unlicensed Antenna 255
- European Community 257
- European Union 1999/5/EC 258
- European Spectrum Usage Rules 260
- Declarations of Conformity 262
- Regulatory Information 264
Relacionado con productos y manuales para Software Extreme Networks Summit WM Series
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales